文献类型：期刊文献

中文题名：反相乳液聚合制备丙烯酰胺-二甲基二烯丙基氯化铵阳离子共聚物

英文题名：Preparation of Acrylamide-dimethyldiallylammonium chloride Cationic Copolymer by Inverse Emulsion Polymerization

作者：赵明[1];王荣民[2];张慧芳[2];李宏洲[3]

第一作者：赵明

机构：[1]定西师范高等专科学校生化系,甘肃定西743000;[2]西北师范大学化学化工学院,甘肃兰州730070;[3]甘肃省化工研究院,甘肃兰州730020

第一机构：甘肃中医药大学定西校区

年份：2010

卷号：15

期号：2

起止页码：20

中文期刊名：甘肃高师学报

外文期刊名：Journal of Gansu Normal Colleges

收录：国家哲学社会科学学术期刊数据库

语种：中文

中文关键词：反相乳液聚合;丙烯酰胺;二甲基二烯丙基氯化铵;阳离子共聚物;复合乳化剂

外文关键词：inverse emulsion polymerization; acrylamide; dimethyldiallylammonium chloride; cationic copolymer; complex emulsifier

摘要：采用反相乳液聚合法,以液体石蜡为连续相、丙烯酰胺和二甲基二烯丙基氯化铵水溶液为分散相、N,N′-亚甲基双丙烯酰胺为交联剂、过硫酸铵为引发剂、Span-80和OP-10为复合乳化剂,制备了丙烯酰胺(AM)-二甲基二烯丙基氯化铵(DMDAAC)阳离子共聚物;考察了引发剂含量、单体AM与DMDAAC的摩尔配比、复合乳化剂Span-80与OP-10的质量配比及含量、聚合温度、聚合体系pH等对AM-DMDAAC阳离子共聚物性能的影响.较佳的聚合条件为:过硫酸铵占单体总质量的1.0%,n(AM):n(DMDAAC)=1.6,m(Span-80):m(OP-10)=96:4(Span-80和OP-10复合乳化剂的亲水亲油平衡值约为4.7),Span-80和OP-10占油相质量的6%,聚合温度40℃,聚合体系pH约为5.0.在此聚合条件下,制得的AM-DMDAAC阳离子共聚物的粘度较大,稳定性较好.
Cationic copolymer of acrylamide and dimethyldiallylammonium chloride was prepared by inverse emulsion polymerization, with liquid paraffin as continuous phase, acrylamide and dimethyldiallylammonium chloride aqueous solution as dispersing phase, N, N＇-methylene-bisacrylamide as cross-linking agent, ammonium persulfide as initiating agent, and Span-80 and OP-10 as complex emulsifier. The influences of some factors on viscosity of the obtained cationic copolymer were investigated, namely initiator dosage, mol ratio of AM to DMDAAC, mass ratio of Span-80 to OP-10, complex emulsifier dosage, reaction temperature and pH of polymerization system. Optimal conditions are： mass fraction of ammonium persulfide in acrylamide and dimethyldiallylammonium chloride 1.0%, n （AM） ： n （DMDAAC） =l.6,m （Span -80） ： m （OP -10） = 96 ： 4 （Span-80 and OP-10 complex emulsifier with hydrophiliclipophilic balance value about 4.7）, mass fraction of Span-80 and OP-10 in continuous phase 6%, temperature 40℃ and pH of polymerization system about 5.0. The obtained cationic copolymer is with high viscosity and stability. The copolymerization process is easily to be operated and environmental friendly. It has big potential for application in industry.